Products

Fresh air intake hood for attachment to outside wall.Single wall galvanized steel Use this 3" Z-Vent fresh air intake hood to bring in fresh air to...

Flat Roof/Chimney Flashing For use with conjunction with a rain cap or storm collar for vertical installations of the Z-Flex pipe on flat roofs. Z...

Z-Flex 3" to 24" Double-Wall Thimble, Stainless Steel Adjustable Use with double-wall pipe going through a combustible wall. Features: • Width can...

Designed for use in a vertically-installed Z-Vent. Supports the vent run above the flashing. Also has built in storm collar. Also for use with a ro...

This termination coupling can be used as the last part of a horizontal venting system if you wish to exhaust straight out the side wall. The produc...

Termination hood for horizontal exhaust vents, single wall stainless steel The termination hood is the final piece in a horizontal venting system f...

3", 4" or 5" Wide (Extended) Version of the Stainless Steel Adjustable Wall Thimble The 3" and 4" diameter versions of this thimble have a length ...

Useful in colder climates for preventing freezing air from flowing back into the heat exchanger and freezing it and damaging the heater Specificat...

Z-Vent by Novaflex Horizontal Drainpipe with 3/8" Condensation Drain Port. Available in 3" or 4" pipe diameters. Z-Flex Z-Vent is approved for Cate...

Z-Vent Flashing 0-30° This roof flashing for use with a rain cap and storm collar for vertical installations of the Z-Vent stainless steel double ...

Z-Vent Double Wall Pipe Z-Flex is the leading manufacturer of specialty venting systems for furnaces, boilers, tankless water heaters, water heater...

Rain Cap with Wind Band for Single Wall Pipe This rain cap was designed to terminate a vertical stack to prevent the entrance of rain and debris in...

Z-Vent Adjustable Roof Flashing, single wall for various diameters. Standard roof slope. Adjustable from 0° to 30° (0/12 to 6/12) pitch Features: ...

15, 30, 45 or 90 Degree Stainless Steel Elbow in diameters from 3" to 24".Choose your variant in the menu. Features: • Simple gasketed connection ...

A: 3"B: 4"C: 7" Z-Flex Stainless Steel Increaser, 3" to 4" Used to upsize a vent system. Features • Vent material: AL29-4C stainless ste...

A: 3"B: 5"C: 8.15" Z-Flex Stainless Steel Increaser, 3" to 5" (not eccentric) Used to upsize a vent system. Features • Vent material: AL...

A: 4"B: 5"C: 7" Z-Flex Stainless Steel 4" to 5" Pipe Diameter Increaser (not eccentric) Used to upsize a vent system. Recommended for us...

A: 4"B: 6"C: 8.15" Z-Flex Stainless Steel Increaser, 4" to 6" (not eccentric) Used to upsize a vent system. Features • Vent material: AL...

A: 4"B: 8"C: 10.3" Z-Flex Stainless Steel Increaser, 4" to 8" (not eccentric) Used to upsize a vent system. Features • Vent material: AL...

A: 5"B: 6"C: 7" Z-Flex Stainless Steel Increaser, 5" to 6" Used to upsize a vent system. This part is not the eccentric (longer length) ...

A: 6"B: 7"C: 7" Z-Flex Stainless Steel Increaser, 6" to 7" (not eccentric) Used to upsize a vent system. Features • Vent material: AL29-...

Flat flashing provides weather protection at the spot where the vent penetrates your chimney or roof. Fits flat or slightly sloped (up to 5°) roofs...

Z-Vent Tee Cap with Drain A tee cap with drain is needed at the bottom of a vertical vent stack. A high temperature silicone tube is available sep...

Stainless Steel Wall Thimble, Standard (not Wide) WidthOn this page, choose from 3" to 24" diameter pipe sizes The 3" and 4" diameter versions of ...