Single Wall Stainless Steel Venting

NovaFlex Z-Flex Single-wall Z-Vent Pipe Z-Flex is the leading manufacturer of specialty venting systems for furnaces, boilers, tankless water heate...

15, 30, 45 or 90 Degree Stainless Steel Elbow in diameters from 3" to 24".Choose your variant in the menu. Features: • Simple gasketed connection ...

This stainless steel adapter is compatible with certain Paloma, Rheem, Noritz heaters, plus the Eccotemp FVI12 and i12 series. It converts the flue...

Useful in colder climates for preventing freezing air from flowing back into the heat exchanger and freezing it Also, use this part to drain conde...

Z-VENT Wall Mounting Water Heater Vent Kit. 4" Diameter, single wall venting system. Save time and money with this convenient, preconfigured vent k...

Z-Vent appliance adapter 3" to 24" Appliance adapters connect your boiler or tankless water heater to the proper Z-Flex / Z-Vent diameter. Most ta...

Designed for use in a vertically-installed Z-Vent. Supports the vent run above the flashing. Also has built in storm collar. Also for use with a ro...

Stainless Steel Wall Thimble, Standard (not Wide) WidthOn this page, choose from 3" to 24" diameter pipe sizes The 3" and 4" diameter versions of ...

Z-VENT Horizontal Wall Mounting Vent Kit for 5" Diameter Heater Flues Save time and money with this convenient, preconfigured vent kit for tankless...

Rain Cap with Wind Band for Single Wall Pipe This rain cap was designed to terminate a vertical stack to prevent the entrance of rain and debris in...

3", 4" or 5" Wide (Extended) Version of the Stainless Steel Adjustable Wall Thimble The 3" and 4" diameter versions of this thimble have a length ...

Vent Termination Hood with backflow preventer (damper). Single not double wall pipe, but will work properly with double wall pipe. Essential for ta...

Sta-Rite Pentair Pool Heater Adapter, 4" Diameter by Z-Flex Z-Vent This adapter creates a way to connect your Pentair pool heater to Z-Vent's Clas...

Termination hood for horizontal exhaust vents, single wall stainless steel The termination hood is the final piece in a horizontal venting system f...

Pentair Sta-Rite 77707-0087 Stainless Steel MasterTemp Pool Heater Adapter, 4" Diameter This adapter creates a way to connect your Pentair MasterT...

Useful in colder climates for preventing freezing air from flowing back into the heat exchanger and freezing it and damaging the heater Specificat...

Wall termination for horizontal vents Features and benefits ◊ Special design resists winds that affect the flue's gas flow◊ Flat surface parallel ...

This termination coupling can be used as the last part of a horizontal venting system if you wish to exhaust straight out the side wall. The produc...

This 3" horizontal (wall-hung) stainless steel by Z-Vent contains all the basic components to mount your tankless water heater on the wall, and ven...

Vertical Drainpipe with Condensation Drain, Single Wall, Class II, III, IV Stainless SteelVarious diameters from 3", 4" 5" up to 14" Use this part ...

Z-Vent by Novaflex Horizontal Drainpipe with 3/8" Condensation Drain Port. Available in 3" or 4" pipe diameters. Z-Flex Z-Vent is approved for Cate...

3" Horizontal Stainless Steel Z-Vent wall-hung water heater vent kit for Eccotemp i12-NG, Eccotemp i12-LP, Eccotemp FVI12-NG, Eccotemp FVI12-LP, 20...

Z-Vent Adjustable Roof Flashing, single wall for various diameters. Standard roof slope. Adjustable from 0° to 30° (0/12 to 6/12) pitch Features: ...

UL-listed Flexible Stainless Steel Round Liner with patented, airtight triple lock construction. Use as chimney liner to vent stove and water heate...

Useful in colder climates for preventing freezing air from flowing back into the heat exchanger, freezing it and damaging the heater Specification...

A: 3"B: 4"C: 7" Z-Flex Stainless Steel Increaser, 3" to 4" Used to upsize a vent system. Features • Vent material: AL29-4C stainless ste...

Useful in colder climates for preventing freezing air from flowing back into the heat exchanger and freezing it and damaging the heater Specificat...

Z-Flex Z-Vent Single Wall Boot Tee This Boot Tee allows you to connect horizontal and vertical sections of pipe with low flow resistance. A Tee Cap...

Use this part to reduce the diameter of your single wall pipe. This is the way to downsize a vent system from a bigger to a smaller diameter. • Ve...

Z-Vent Z-Flex 3" or 4" Condensation Drain Vertical Draintee for Single Wall Features: • Simple gasketed connection requires no sealant• Offers the...

Z-Flex Extreme Weather Rain Cap, available 3, 4 or 5 inch diameters Use this rain cap if the installation region sometimes experiences heavy or dri...

3" Horizontal Stainless Steel Z-Vent Wall Hung Water Heater Vent Kit for the Eccotemp FVI-12, Eccotemp i12, 20HI-LP and 20HI-NG, 40HI-LP and 40HI-N...

Z-Vent Tee Cap with Drain A tee cap with drain is needed at the bottom of a vertical vent stack. A high temperature silicone tube is available sep...

The 3" or 4" Z-Flex vertical single-wall vent kit is designed for use with through-roof installations of indoor water heaters. Made of durable AL-2...

Vent Pipe Wall Support for Single Wall Pipe by Z-Vent Z-Flex (NovaFlex Group) Can be used with both horizontal and vertical pipe runs. Vent suppor...

This page includes all diameters 3 inch to 24 inch) for the Fire Stop Spacer for single wall vent pipe. Use this with vertical venting systems from...

Flat flashing provides weather protection at the spot where the vent penetrates your chimney or roof. Fits flat or slightly sloped (up to 5°) roofs...

Z-Vent (NovaFlex Group) Single Wall or Double Wall* Clamp Band This Clamp Band is used to support the weight of the vent pipe. It clamps around th...

This page includes all diameters for the Fire Stop Support for Single Wall Vent Pipe. The application is for vertical venting systems. This gadget ...

A: 4"B: 6"C: 8.15" Z-Flex Stainless Steel Increaser, 4" to 6" (not eccentric) Used to upsize a vent system. Features • Vent material: AL...

Kit for venting horizontally through a wall for several different Bosch tankless water heater models. Pipe diameter is the required 3" diameter and...

Is the room fairly small where your 4" exhaust tankless water heater is to be installed? Does the room lack sufficient supply of fresh air? Then yo...

Is the room fairly small where your 3" exhaust tankless water heater is to be installed? Does the room lack sufficient supply of fresh air? Then yo...

The 3" Eccotemp vertical single-wall vent kit is designed for use with through-roof installations of various models of indoor water heaters, includ...

Z-Vent Steep Adjustable Roof Flashing, single wall for various diameters Adjustable from 30° to 45° (7/12 to 12/12) pitch Use this flashing for ste...

Z-Flex Z-Vent 3" or 4" Diameter Termination 90-degree Elbow Includes a metal grid to prevent animals and debris from entering the exhaust system. S...

The 3" Bosch vertical single-wall vent kit is designed for use with through-roof installations of the Bosch Therm 940ES, 830ES, 660EF 2400E, 250SX,...